Introduction Why Use OPNET Modeler Computer Science Essay

Introduction Why Use OPNET Modeler Computer Science Essay OPNET Modeler is a very good tool for network designing and simulation. OPNET Modeler was selected because most of the wired and wireless network components are available in the OPNET 15.0 Modeler. In this version a number of different models can be created to simulate, analyze and compare their results. This chapter explains how the different wired and wireless network has been designed and simulated in OPNET Modeler. In this project different scenario for Ethernet, DSL, Wi-Fi, and WiMAX in two different projects has been created in OPNET Modeler 15.0 . There is also a comparison between the wired and wireless networks. The Ethernet network is compared with the Wi-Fi network and the DSL network is compared with the WiMAX network. Overview of OPNET Modeler OPNET stands for Optimized Network Engineering Tool. The OPNET Modeler is a very powerful tool for the network modeling and simulation. The purpose of the OPNET Modeler is to optimize cost, efficiency, performance, viability and scalability characteristics of the network. In addition OPNET Modeler has a huge library of nodes(fixed, mobile or satellite), links(simplex, duplex, wired or wireless), and subnets, which are used to design and simulate network configuration, protocols, traffic and end user applications. OPNET Modeler has three hierarchical levels or editors. These are Project Editor Project editor is also known as network editor. The project editor is the key staging area for modeling a network simulation. In the project editor a network can be created by using the nodes, link, and subnets from the standard library, then select statistics, run the simulation and view the results of the network. FIGURE: Node Editor To built models of nodes the node editor is used. Node editor specifies the internal structure of the network node. The node includes workstations, satellite terminals, switches, and remote sensors. The OPNET node has a modular structure. The packets and status information are exchanged between modules which are connected via packet streams or statistic wires. Every module performs specific function, such as generating packets, processing packets, transmitting and receiving packets or queuing packets. FIGURE Process Editor The process editor is used to design process models, which controls the basic functionality of node models generated in the node editor. The process models are represented by Finite State Machines (FSMs). The FSMs are generated with icons, which show states and lines which shows transitions between states. The process models are expressed in C or C++ language. Figure In this chapter four different scenarios are discussed. These are Scenario1: Ethernet Network Model In this scenario a new wired network for Ethernet is created in OPNET Modeler as shown in figure. This scenario is created for campus network. In this scenario seven workstations are connected to the switch. With the help of a router the switch is connected to the server. The switch is connected to the router which is connected to the server. Ethernet links are used to connect all these nodes with each other. The server provides different applications used for the workstations. For this network model we also need to define the applications and profiles by adding a node for the application and profile. The workstations are associated with the profiles in order to use different applications. H:snapshots 1ETHERNET.bmp Figure Ethernet Network Model The nodes used in this scenario is Node Name Description Applications Profiles Server Router Switch Workstation How to configure Nodes The configuration of each node is as follow Application Configuration The application configuration is the most important node in the network design. By default the application configuration has a maximum of sixteen services, which are supported by the OPNET Modeler. These are http, ftp, e-mail, print etc. In this scenario the default services are selected as shown in the figure To configure the application node right click on it, select Edit Attributes a dialogue box will open. Change the name field value to application. Expand the Application Definitions row, select the default option while left other setting at default as shown in the figure. H:SNAPSHOT22)ETHERNET APPLICATIN CONFIG.bmp Figure: Ethernet Application Configuration Profile Configuration The profile configuration allows us to define a user or a group of user to the application services supported by the network. For this scenario one profile is defined namely shahid. The profile node can be configured by expanding the profile configuration row. Define the profile namely shahid also define the applications and change the operation mode to simultaneous while left the other setting at default as shown in figure To configure the profile configuration right click on it, select Edit Attributes a dialogue box will appear. Change the name field value to profiles. Expand the profile configuration row, select edit. Then define the profile namely shahid also define the applications and change the operation mode to simultaneous while left the other setting at default as shown in figure. H:SNAPSHOT22)ETHERNET PROFILE CONFIG2.bmp Figure: Ethernet Profile Configuration Server Configuration The server can generate the applications traffic such as http, ftp, e-mail, print etc. This traffic can be sent to the workstations with the help of router and switch which are connected through Ethernet links. In the server configuration, three applications supported services were defined namely http, ftp, and e-mail while all other settings are left at default as shown in figure. H:SNAPSHOT22)ETHERNET SERVER.bmp Figure Ethernet Server Configuration Workstation Configuration The workstation can also generate the applications traffic, which can be sent to the server through the network to the server. The workstation can be configured by selecting the Application Supported Profiles namely shahid while left all the other parameters at default as shown in the figure. H:SNAPSHOT22)ETHERNET WKSTN CONFIG.bmp Figure: Ethernet Workstation Configuration Router and Switch The functions of both the router and switch are almost the same. Both are forwarding the traffic to the end nodes. The router and switch are connected to each other through Ethernet link. Scenario2: WLAN Network Model In scenario 2 a wireless network model for WLAN is created in OPNET Modeler as shown in figure. This scenario is also created for the campus network. This scenario is similar to scenario1 with slight changes. In scenario2 the switch of scenario 1 is replaced with the wireless access point (AP) and also the workstations are replaced with the wireless LAN workstations. The main function of the wireless access point is to transmit and receive the wireless signals. The access point is connected to the router which is then connected to the server through Ethernet link as shown in figure. C:Usersshahid aliDesktopUntitlrgregreeddfgdfg.png Figure: WLAN Network Model The nodes used in scenario2 is Node Name Description Applications Profiles Server Router Wireless Access Point Wireless LAN Workstations The configuration of all the nodes except the wireless access point (AP) and wireless workstations are the same which are discussed in scenario1. The configuration of the wireless access point (AP) and the wireless workstations are as follow. Wireless access point (AP) configuration The wireless access point (AP) transmits and receives the wireless signals. The wireless access point can be configured by expanding the wireless LAN parameters. The access point functionality should be enabled so that this node can transmit the wireless signals. The BSS Identifier value is set to 0. If there is another wireless access point (AP) in the network then its BSS Identifier value must be different. The other setting is left at default as shown in figure. H:SNAPSHOT22)WLAN AP CONFIG.bmp Figure: WLAN Wireless Access Point (AP) Configuration Workstation configuration The workstation configuration is the same as the workstation configuration in scenario1. But in this scenario the BSS identifier value for the workstations is also defined. The BSS Identifier value is set to 0. This value must be the same as the wireless access point BSS Identifier value. The access point functionality is disabled for the workstations. The remaining settings are left at default as shown in figure. H:SNAPSHOT22)WLAN WKSTN APLICATION AND WIRELASS CONFIG.bmp Figure: WLAN Workstations Configuration Scenario3: DSL Network Model In this scenario a wired network model is created for the DSL using the OPNET Modeler. In this scenario four workstations are connected to the switch through the Ethernet links. The switch is connected to DSL modem. The DSL modem is connected to the DSLAM via the DSL links. The type of DSL used for this scenario is Asymmetric DSL (ADSL). The ADSL has a high downstream data rate than the upstream data rate. The function of the DSLAM is to linked several users to the high speed backbone network. The DSL modem is used to send and receive signals. The DSL modem has internal signal splitter that carries voice signal on the low frequencies and carries data signal above that frequencies. With the help of IP cloud the DSLAM is connected to the server via the PPP link. The figure shows the DSL network model. C:Usersshahid aliDesktopSHANPSHOT33DSL.bmp Figure: DSL Network Model The nodes and links used in scenario3 are Node/Link Name Description Applications Profiles Server Router Switch Workstation IP Cloud DSLAM DSL modem PPP Link DSL Link Ethernet Link The configuration of each node and applications taken for this scenario is the same as discussed in scenario1 and scenario2. For scenario3 the profile name is different, here the profile name is SHAH. Scenario4: WiMAX Network Model In scenario4 a wireless network model for the WiMAX is created using OPNET Modeler. This scenario is the same to scenario3 but there is a slight changes. A new node is added for the WiMAX configuration. Without this node the WiMAX network will not work. In this scenario the DSL modem is replaced with the WiMAX basestation, the switch is replaced with the subscriber station and the workstations are replaced with the wireless workstations. The WiMAX basestation will transmits the wireless signal over a long distance. The subscriber station which is found at the costumer site receives this signal, which is then sent to the wireless workstations. The subscriber station and the WiMAX basestation communicate through air interface-. The WiMAX basestation is communicating to the server through the ip cloud and router via PPP link. The figure shows WiMAX network model. C:Usersshahid aliDesktopSHANPSHOT33WIMAX.bmp Figure: WiMAX Network Model The nodes and links used for scenario4 are Node/Link Name Description Applications Profiles Wimax config Server Router Ip cloud WiMAX basestation Subscriber station Workstation Link